Follow the instructions below to run the Bare-Metal Restore of Archive Point.
 | Note Bare-Metal Restore of Archive Points is the same as Bare-Metal Restore of a usual Recovery Point. |
1. Click "Recovery Points" in the Main Menu to open the "Recovery Points" screen.
2. Select a Server from the drop-down menu located on the "Recovery Points" list toolbar.
3. Select a Disk Safe from the drop-down menu located on the "Recovery Points" list toolbar.
4. Select the "Archive Points" tab.
5. In the "Archive Points" list, click on the "Bare-Metal Restore" icon in the "Actions" column for the Archive Point from which you are going to restore.
6. The "Bare-Metal Restore" window opens.
7. Look through the information on the Introduction screen and click "Next."
8. On the next page, select the file system you want to restore. All available file systems are listed. At least one must be selected by clicking on the appropriate checkbox.
| Tip To display file system properties, click on the "Plus" icon in front of the file system name. The following data is provided for each file system:
|
Click "Next" to proceed to the following step.
9. On the next screen, select one of the following options:
- Restore to Original Host - The same Server Name/IP address and port as the original Server. Connects to the Server name and uses the port configured when the Recovery Point was created.
- Restore to Alternate Server - Connects to the selected Server's hostname and the specified port. The Server must have been added already to the system.
- Restore to Alternate Host Name/IP - Connect to the specified hostname and port. This option allows you to Restore to a Host with a Host Name/IP address different than the original Host. For example, if the PXE host has a different IP, specify the IP address.
To restore to the Server where the system was installed previously, choose the first option ("Restore to Original Host"). This is the only option that makes sense when you perform Bare-Metal Restore using Server Live CD or Server PXE Boot.
If you chose to restore to an alternate Server added to the system, select the second option ("Restore to Alternate Server"). Then select the Server from the drop-down list. The Server must be running the Backup Disaster Recovery Boot Media and should be known to the Backup Manager. When a Server is booted into Disaster Recovery Media, no authentication will be required.
If you chose to restore to an alternate Server not added to the system, select the last option ("Restore to Alternate Host Name/IP"). Then enter the Hostname or IP address of the alternate Server. This option should be selected when you perform Bare-Metal Restore using Agent Live CD or Agent PXE Boot.
Click "Next" to proceed to the following step.
10. On the "Restore Storage Configuration" screen, select one of the following options:
- Select Storage Configuration to Restore - Selecting this option lets you choose storage configuration.
- Use Existing Storage Configuration - Bare-Metal Restore will use the storage configuration already present on the target Server. If you choose this step, proceed to the step 16.
Click "Next" to proceed to the following step.
11. On the next screen, select one of the following options:
- Use Existing Partition Tables on Host - Bare-Metal Restore will use the partition layout already present on the target Server. This option should almost never be used when performing Bare-Metal Restore.
- Select Partition Tables to Restore - Selecting this option lets you pick partition tables from the Recovery Point to restore to the target Server. In most cases, you should select this option.
Click "Next" to proceed to the following step.
12. If you select the "Select Partition Tables to Restore" option, then three additional steps arise:
- Select Partition Tables
- Map Partition Tables
- Restore Partition Tables
12.1 Selecting Partition Tables
Select the partition table layout(s) for the filesystems you want to restore.
| Tip To display the partition table properties, click on the "Plus" icon in front of the partition table's name.
|
Click "Next" to proceed to the following step.
12.2 Mapping Partition Tables
After choosing partition tables to restore, map the selected Partition Table(s) Recovery Points to physical Disks in the Target Server. From the drop-down menu named "Click to Edit," select the physical Disks to which you are going to restore.
You are provided a table that allows you to map the chosen Partition Tables to physical Disks on the Target Server. You can see as many lines in the table as the Partition Tables selected to restore. Each Partition Table must be mapped to a physical Disk on the Target Server before proceeding.
After selecting the Disks, click on "Next" to proceed to the next page.
12.3 Restoring Partition Tables
Perform the partition table restore by clicking on the "Restore Partition Tables" button. Once confirmed, the Partition Table Restore will be initiated. A busy indicator will be displayed while the restore is in progress. Restoring the partition table should not take a lot of time because the partition table fits into one sector - 512 bytes.
| Notice Restored partition tables will overwrite the existing partition table layout on the target devices. |
When the process is over, click "OK" in the notification pop-up.
Click "Next" to proceed to the following step.
13. On the appeared screen, select one of the following options:
- Use Existing Software RAID Devices on Host - Bare-Metal restore will use Software RAID Devices that already exist on host.
- Select Software RAID Devices to restore - Allows you to choose Software RAID Devices to restore. If you choose this option, go through all of the Software RAID steps. For more information see Performing Bare-Metal Restore with RAID (MD).
Click on "Next" to proceed to the next page.
14. On the appeared screen, select one of the following options:
- Use Existing LVM Volume Groups on Host - Bare-Metal restore will use LVM Volume Groups on host.
- Select LVM Volume Groups to Restore - Allows you to choose LVM Volume Groups to restore. If you choose this option, go through all of the LVM Volume Groups steps. For more information see Perfoming Bare-Metal Restore with LVM.
Click on "Next" to proceed to the next page.
15. The following step requires you to map the chosen file systems to the devices on the target machine.
From the drop-down menu called "Click to Edit," select destination devices for each source file system.
 | Notice The target device must be large enough to hold the file system. |
| Notice Each target device can be selected once only. |
Click "Next" to proceed to the following step.
16. Then you need to define the following options:
- Reboot After Restore - Reboots the target host after the restore is performed. Select this check-box to reboot your Server after the Bare-Metal Restore is complete. This option is very useful since you have to reboot the target host after restore anyway.
- Check Filesystems After Restore - Checks the file systems after the restore is performed.
Click "Next" to proceed to the following step.
17. On the "Summary" page, you will need to confirm the selected Bare-Metal Restore options. Each selected file system is listed along with the name of the target device to which the file system is being mapped.
Click "Restore" to start the Bare-Metal Restore task.
| Tip The Task results can be sent via email as a Report. See Reporting. |
18. The Restore process starts and can take awhile. You can go to the "Task History" screen to observe the task progress. See Access task history.
The Task History page displays the State, Alert, Type, Progress percentage, and the Started time stamp of the Bare-Metal Restore process.
| Note You can find more information about the Restore process by reading the Log Messages. The Log Messages for the selected Task are displayed at the bottom of the page.
|
19. When the process is complete, you can reboot the server you just restored by pressing <Ctrl><Alt><Del> or by executing the reboot command in the root shell.
| Notice Make sure you eject the Disk from the CD-ROM drive so the server will boot from the hard Disk. |
| Note If the Disk you used for your Bare-Metal Restore is larger than the Disk you backed up previously, the free space on the new Disk will remain free. You can create a new Partition in this space. |
